When the point at which a force acts moves, the force is said to have done work.
When the force is constant, the work done is defined as the product of the force and distance moved.
Consider the example in Figure 3.1, a force F acting at the angle q moves a body from point A to point B.
Figure 3.1: Notation for work done by a force
The distance moved in the direction of the force is given by
So the work done by the force F is
Work done = Fs
When the angle is 90 then the work done is zero.
The SI units for work are Joules J (with force, F, in Newton's N and distance, s, in metres m).
How much work is done when a force of 5 kN moves its point of application 600mm in the direction of the force.
Solution
Find the work done in raising 100 kg of water through a vertical distance of 3m.
Solution
The force is the weight of the water, so
Forces in practice will often vary. In these cases Equation 3.1 cannot be used. Consider the case where the force varies as in Figure 3.2
For the thin strip with width ds - shown shaded in Figure 3.2 - the force can be considered constant at F. The work done over the distance ds is then
This is the area of the shaded strip.
The total work done for distance s is the sum of the areas of all such strips. This is the same as the area under the Force-distance curve.
Figure 3.2: Work done by a variable force
So for a variable force
In general you must uses some special integration technique to obtain the area under a curve. Three common techniques are the trapezoidal, mid-ordinate and Simpson's rule. They are not detailed here but may be found in many mathematical text book.
A body which has the capacity to do work is said to possess energy.
For example , water in a reservoir is said to possesses energy as it could be used to drive a turbine lower down the valley. There are many forms of energy e.g. electrical, chemical heat, nuclear, mechanical etc.
The SI units are the same as those for work, Joules J.
In this module only purely mechanical energy will be considered. This may be of two kinds, potential and kinetic.
Only gravitational potential energy will be considered here. It may be described as energy due to position relative to a standard position (normally chosen to be he earth's surface.)
The potential energy of a body may be defined as the amount of work it would do if it were to move from the its current position to the standard position.
Formulae for gravitational potential energyA body is at rest on the earth's surface. It is then raised a vertical distance h above the surface. The work required to do this is the force required times the distance h.
Since the force required is it's weight, and weight, W = mg, then the work required is mgh.
The body now possesses this amount of energy - stored as potential energy - it has the capacity to do this amount of work, and would do so if allowed to fall to earth.
Potential energy is thus given by:
What is the potential energy of a 10kg mass:
- 100m above the surface of the earth
- at the bottom of a vertical mine shaft 1000m deep.
a)
b)
Kinetic energy may be described as energy due to motion.
The kinetic energy of a body may be defined as the amount of work it can do before being brought to rest.
For example when a hammer is used to knock in a nail, work is done on the nail by the hammer and hence the hammer must have possessed energy.
Only linear motion will be considered here.
Let a body of mass m moving with speed v be brought to rest with uniform deceleration by a constant force F over a distance s.
Using Equation 1.4
And work done is given by
The force is F = ma so
Thus the kinetic energy is given by
When a body with mass m has its speed increased from u to v in a distance s by a constant force F which produces an acceleration a, then from Equation 1.3 we know
multiplying this by m give an expression of the increase in kinetic energy (the difference in kinetic energy at the end and the start)
Thus since F = ma
but also we know
So the relationship between kinetic energy can be summed up as
Work done by forces acting on a body = change of kinetic energy in the body
A car of mass 1000 kg travelling at 30m/s has its speed reduced to 10m/s by a constant breaking force over a distance of 75m.
Find:
- The cars initial kinetic energy
- The final kinetic energy
- The breaking force
a)
b)
c)
Change in kinetic energy = 400 kJ
By Equation 3.5 work done = change in kinetic energy so
The principle of conservation of energy state that the total energy of a system remains constant. Energy cannot be created or destroyed but may be converted from one form to another.
Take the case of a crate on a slope. Initially it is at rest, all its energy is potential energy. As it accelerates, some of it potential energy is converted into kinetic energy and some used to overcome friction. This energy used to overcome friction is not lost but converted into heat. At the bottom of the slope the energy will be purely kinetic (assuming the datum for potential energy is the bottom of the slope.)
If we consider a body falling freely in air, neglecting air resistance, then mechanical energy is conserved, as potential energy is lost and equal amount of kinetic energy is gained as speed increases.
If the motion involves friction or collisions then the principle of conservation of energy is true, but conservation of mechanical energy is not applicable as some energy is converted to heat and perhaps sound.
A cyclist and his bicycle has a mass of 80 kg. After 100m he reaches the top of a hill, with slope 1 in 20 measured along the slope, at a speed of 2 m/s. He then free wheels the 100m to the bottom of the hill where his speed has increased to 9m/s.
How much energy has he lost on the hill?
Solution
Figure 3.3: Dimensions of the hill in worked example 3.5
If the hill is 100m long then the height is:
So potential energy lost is
Increase in kinetic energy is
By the principle of conservation of energy
Power is the rate at which work is done, or the rate at which energy is used transferred.
A power of 1W means that work is being done at the rate of 1J/s.
Larger units for power are the kilowatt kW (1kW = 1000 W = 103 W) and
the megawatt MW (1 MW = 1000000 W = 106 W).
If work is being done by a machine moving at speed v against a constant force, or resistance, F, then since work doe is force times distance, work done per second is Fv, which is the same as power.
A constant force of 2kN pulls a crate along a level floor a distance of 10 m in 50s.
What is the power used?
Solution
Alternatively we could have calculated the speed first
and then calculated power
A hoist operated by an electric motor has a mass of 500 kg. It raises a load of 300 kg vertically at a steady speed of 0.2 m/s. Frictional resistance can be taken to be constant at 1200 N.
What is the power required?
Solution
From Equation 3.7
A car of mass 900 kg has an engine with power output of 42 kW. It can achieve a maximum speed of 120 km/h along the level.
- What is the resistance to motion?
- If the maximum power and the resistance remained the same what would be the maximum speed the car could achieve up an incline of 1 in 40 along the slope?
Figure 3.4: Forces on the car on a slope in Worked Example 3.8
First get the information into the correct units:
a) Calculate the resistance
b)
Or in km/h
The moment of a force F about a point is its turning effect about the point.
It is quantified as the product of the force and the perpendicular distance from the point to the line of action of the force.
Figure 3.4: Moment of a force
In Figure 3.5 the moment of F about point O is
Figure 3.6: A couple
The moment of a couple about any point in its plane is the product of one force and the perpendicular distance between them:
The SI units for a moment or a couple are Newton metres, Nm.
In engineering the moment of a force or couple is know as torque. A spanner tightening a nut is said to exert a torque on the nut, similarly a belt turning a pulley exerts a torque on the pulley.
Work done by a constant torque
Let a force F turn a light rod OA with length r through an angle of q to position OB, as shown in Figure 3.7.
Figure 3.7: Work done by a constant torque
The torque TQ exerted about O is force times perpendicular distance from O.
Now work done by F is
s is the arc of the circle, when qis measure in radians
The work done by a constant torque TQ is thus the product of the torque and the angle through which it turns (where the angle is measured in radians.)
As the SI units for work is Joules, TQ must be in Nm
Power transmitted by a constant torque
Power is rate of doing work. It the rod in Figure 3.7 rotates at n revolutions per second, then in one second the angle turned through is
radians, and the work done per second will be, by Equation 3.11
as angular speed is
then
A spanner that is used to tighten a nut is 300mm long. The force exerted on the end of a spanner is 100 N.
- What is the torque exerted on the nut?
- What is the work done when the nut turns through 30° ?
a)
Calculate the torque by Equation 3.10
b)
Calculate the work done by Equation 3.11
An electric motor is rated at 400 W. If its efficiency is 80%, find the maximum torque which it can exert when running at 2850 rev/min.
Solution
Calculate the speed in rev/s using Equation 3.12
Calculate the power as the motor is 80% efficient
Work done by a variable torque
In practice the torque is often variable. In this case the work done cannot be calculated by Equation 3.11, but must be found in a similar way to that used for a variable force (see earlier.)
Figure 3.8: Work done by a variable torque
The work done when angular displacement is dqis TQdq. This is the area of the shaded strip in Figure 3.8. the total work done for the angular displacement q is thus the area under the torque/displacement graph.
For variable torque
A machine requires a variable torque as shown in Figure 3.9, Find:
- The work done per revolution
- The average torque over one revolution
- The power required if the machine operates at 30 rev/min
Figure 3.9: Torque requirement for Worked Example 3.12
Solution
a)
From Equation 3.13
for one revolution
b)
Average torque is the average height of figure OABCDE = area /2p
c)
No comments:
Post a Comment